Shopping Cart

We’re here to help

(03) 9210 0400

SP Smart Battery Charger 8 Stage Car 4WD 12 Volt 40 Amp LED display SP61087

In stock
SKU# SPASP61087
Special Price $762.50 Regular Price $910.25
Save 16.23% off

SPECIFICATIONS:
• Current Output: 40 Amp
• Output Voltage (Nom): 12 Volt
• Battery Type Supported: Gel/Calcium/Lead Acid - AGM
• Charge Stages: 8 Stages

FEATURES:

  • Built-in microchip charging control and monitoring system
  • Zero volt minimum start – can charge a completely flat battery
  • Optimally designed charging cycle designed for Lead Acid / AGM, Gel, & Calcium, starting and deep cycle batteries
  • Automatic adjustment of charging voltages according to environmental temperature
  • Overcharge protection, protecting the battery from damage due to overcharging
  • Reverse polarity, short circuit, overload and high temperature protection
  • LED display percentage of battery charge, larger
  • Battery Testing function while charging (faulty batteries cause the full battery bar display to flash).

WARNING: Batteries contain corrosive liquid. Always wear approved gloves and goggles when handling batteries or battery acid.If battery acid contacts skin, wash off immediately and contact a doctor for further advice.

CHARGING STAGES

STAGE 1 – “DESULPHATION”

In this initial start-up stage, a high frequency voltage pulse (0.5 sec) assists in “waking up” a deeply discharged battery. This method of pulse charging can also help to reduce build-up of sulphate crystals that may have formed on the battery plates during the time it was discharged. Pulse of 500ms on & 800MS off at 50% of maximum current output for 3 minutes, if the voltage of the battery is > 4 Volts, then the charger progresses to the next stage.

STAGE 2 – “SOFT START”

After the battery is connected, most conventional “Smart” Battery Chargers will immediately apply a high charging voltage and current output. This creates a large amount of gas and heat from the battery and when the consistency of the battery electrolyte / state of cell charge is uneven - (from time to time the consistency of the battery electrolyte can be uneven from daily use) - a full load charging characteristic can result in a period of potentially damaging overcharging. The Soft Start function eliminates this situation by starting the charging process slowly and softly, battery electrolyte and cell charge is able to even out, before receiving the main bulk charge. This significantly improves the battery charging capability and reception.

STAGE 3 – “BULK”

This is the main hard charging stage, where the charger will operate at the maximum rated current output, until the battery reaches a pre-set voltage determined by the battery type selection. Charging time period is determined by the capacity and charge state of the battery.

STAGE 4 – “ABSORPTION”

After the Bulk stage, the charger will automatically begin to reduce its current output depending on the charge acceptance of the battery, while maintaining a constant voltage (determined by the battery type selection - 14.3V GEL / 14.8V Lead Acid, AGM / 15.6V Calcium). When the current reduces to a predetermined threshold level charging will automatically halt, allowing the analysis stage to be performed.

STAGE 5 - “ANALYSIS” (Testing the battery while charging)

After the Absorption charging state, the battery charger will start the “Analysis” stage and will stop charging the battery for 1 minute. At this point, if the battery voltage is sensed at below 12.6V, the battery alarm and faulty battery indicators and alarm will sound. If the battery voltage is equal to or above 12.6V, the next Boost stage will start.

STAGE 6 – “BOOST”

After successfully analysing the battery condition, the charger will enter the Boost charge stage, which will charge at a slightly higher voltage ensuring the battery attains a 100% full charge. The current output is limited at 25% of the maximum rated charger output. When the current drops to the pre-set level or a maximum of 15 minutes is reached the charger will enter the last float charge stage.

STAGE 7 – “FLOAT”

When the charger has finished the Boost stage the Float stage will set its output voltage at 13.3V Gel, 13.7 Lead Acid / AGM or 13.8V Calcium when the charging current gets to <1.2A or a maximum time of 2 hours is reached then the charger will progress to the next stage. If a load is applied and the battery voltage drops to < 12.4 Volts the charger will return and restart from the Absorption stage.

STAGE 8 – “MAINTAIN”

This final stage regulates the fully charged battery. A small pulse charge is applied at 1Hz at a voltage of 13.3V to maintain the battery at its fully charged state and ready to be used at any time. If a load is applied to the battery and the battery voltage drops below 12.4 volts, the charger will restart from the Absorption stage.

More Information
SKU SPASP61087
Brand SP TOOLS
Warranty 12 months
Condition New
Dimension Length (cm) 40
Dimension Width (cm) 25
Dimension Height (cm) 14
Write Your Own Review
Write Your Own Review:SP Smart Battery Charger 8 Stage Car 4WD 12 Volt 40 Amp LED display SP61087
Your Rating

 DELIVERY

At Best Buys Online, we always strive to offer you the lowest shipping prices possible.

On each product page, we provide an online instant shipping quote with multiple options of shipping to your commercial address (for ex: business, farm, workshop) or your house and with or without tailgate.

To learn about our rates, please try our free instant online shipping calculator and you’ll get an immediate response - a shipping quote that is budget-friendly.

PLEASE NOTE: 

PO BOXES : NO parcels above 22kg and/or longer than 1meter can be sent to a PO Box. Signature is required.

1. Goods are shipped once payment is received in full. We strongly advise all customers that they provide a delivery address where someone is available to sign for the goods during business hours. Sometimes, a forklift will be required to unload at the destination. If customers don’t have means to unload, you may be required to pick it up from a designated courier depot, OR pay an extra fee for the tailgate to unload the item when delivering to your nominated address. Please send us a message or call us (03) 9210 0400 to arrange.

2. All courier companies will attempt delivery of your goods once. If no one is home when delivery is being attempted, a note will be left. A re-delivery will incur extra charges. All second deliveries need to be directly organised with the courier company and paid for before goods are delivered.

3. Once in the hands of the couriers, freight times are outside of our control. However all tracking details are forwarded via email upon dispatch and customers are welcome to contact the relevant freight company, or we are happy to attend to any queries you may have.

4. FREE SHIPPING PROMOTION: This only applies to customers in capital cities. Free Shipping does not apply to regional areas. We can send the item to the nearest freight depot, and we will charge you the difference in freight cost to the capital city and your pick-up location. Please call us on (03) 9210 0400 for further information.
PICK-UP OPTION (No Handling Fee applies)

This option allows you to pick up your order from our Melbourne warehouse at no added cost.

Bookings are essential. Collection available at U5/25 Jersey Rd, Bayswater, Vic 3153.

Once your order has been placed, we will contact to let you know when your order will be available for pickup. (Our operating hours are between 8AM to 5PM Monday to Friday and 9am-3pm on Saturday).